REPLACEMENT OF A PULSECODER
- Fanuc 15m Operator Manual
- Fanuc 15m Operator Manual Pdf
- Fanuc Manual Guide I Download
- Fanuc Guide I Operator's Manual
- Fanuc Programming Manual Pdf
Fanuc 15m Manual FANUC Series 15-Model B Descriptions Manual for Gas, Laser, Plasma Cutting Machines B-62082E-1/01 FANUC Series 15/150-Model B Descriptions Manual for Machining Center B-62082E/04 Fanuc Conversational Automatic Programming (CAP) Function II for Lathe Operators Manual B-61804E-2/05 Fanuc 15 Manuals User Guides - CNC. FANUC MANUAL GUIDE i a user-friendly conversational programming platform that makes it easy to perform create part programs right on the shop floor.The innovative programming enables development from a drawing to a production part in a very short time. GE Fanuc Automation Computer Numerical Control Products Series 15 / 150 – Model B Maintenance Manual GFZ-62075E/04 May 1998. Fanuc Series 15i 150i Fanuc Alarm OT032 (REFERENCE POSITION RETURN REQUEST) Fanuc Alarm OT032 NEED ZRN (ABS PCDR) Machine absolute position data in the serial pulse coder is lost. (This alarm is issued when the serial pulse coder has been replaced or when the position feedback signal line of the serial pulse coder is detached.) Action. Zero Return parameter setting procedure for Fanuc 16/18 and 16i/18i Controls. Move the axis to where you think zero return should be. If you can't get to the position you would like, hold in 'P' and 'Cancel' on power up to bypass soft overtravels or you could change the soft overtravel limits to temporarily.
IN A F10/11/12/15 CONTROL.
The method is for AC Servo motors model Types 0,5,10,20,40,50,60,70 and L series. It is
possible to separate and exchange the pulsecoder in model types
1-0 AND 2-0 ,
The pulsecoder in models 3-0,4-0 AND 5-0 Cannot be replaced because it is directly assembled onto the motor.
REMOVAL OF A PULSECODER.
- Remove the red endcap of the motor.
- Look for a small line on one of the three mounting tabs. It should be aligned with a mark on the endbell of the motor if not , Please make one (Never remove the mounting tab bracket from a pulsecoder)
- Remove the rubber cap on the back of the pulse coder.
- Remove the allen head screw from the inside of the pulsecoder.
- Remove the three mounting screws
- Remove the pulsecoder
- If there are two wires on the pulse coder cable that are going to the inside of the motor, cut these wires leaving enough wire to reconnect to the new pulsecoder.
- Remove the four screws that hold the cannon connector to the red endcap. Then remove the small ring holding the connector together.
INSTALLATION OF A NEW PULSECODER.
- Reinstall the connector to the red endcap and connect the overheat wires that are coming out from the inside of the motor.
- Align the coupling of the pulsecoder to the motor shaft
- Reinstall and tighten the allen screw inside the pulsecoder.
- Align the mark on the pulsecoder mounting tab to the mark on the motor. This is very important, this is so that the control knows where the motor rotor shaft position is.
- Reinstall the rubber cap on the back of the pulse coder then put back on the red endcap.
IF AN ABSOLUTE POSITION DETECTOR IS USED, YOU WILL NEED TO RESET THE PULSECODER
MEMORY. THE TWO METHODS ARE LISTED BELOW:
- MANUAL REFERENCE METHOD.
- On the setting page change the machine linear axis Detection units to Metric
- Make parameter 1815 bit 5 a 0 for the axis to be adjusted.
- Turn off/on control .
ALARM “APC ALARM : AXIS NEED ZRN” IS DISPLAYED. Cursor highlighter.
- Reference return the axis. Push reset to clear the alarm
- Return the setting back to Inch.
PARAMETER 1815 BIT 5 IS AUTOMATICALLY CHANGED TO A ONE.
- M.D.I. REFERENCE METHOD (DOGLESS ZERO RETURN)
- Set Parameter 1815 bit 5 to 0 for the axis to be adjusted
- Turn off/on the control
ALARM “APC ALARM : AXIS NEED ZRN” IS DISPLAYED.
- Move the axis to the desired reference point by jog or by the M.P.G.
- Set parameter 1815 bit 5 to a 1
- Turn OFF/ON The control
NOTE:
Dhere dhere naino ko dhere dhere mp3 song free download. If a softovertravel alarm occurs You will need to do the following:
For a 10 Control power on the control holding the – and . In N IPL Mode input a 4 for setting then answer NO to the question “CHECK SOFTOVERTRAVEL AT POWER ON ?”.
For a 11/12 control make the stored stroke limit of the axis in question a very large number. Example +99999999.
For a 15 control power on the control while holding the P and Cancel Keys at the same time
POSITION HAS MOVED AND ALL OFFSETS FOR THAT AXIS HAS CHANGED.
THE GRID SHIFT MAY ALSO HAVE TO BE ADJUSTED.
FANUC Series 0- Model C
![Fanuc 15m operator manual pdf Fanuc 15m operator manual pdf](https://image.slidesharecdn.com/fanuc15mmaintenancemanual-180712071712/95/fanuc-15m-maintenance-manual-2-638.jpg?cb=1531379897)
Confirm device setting and parameter.
Setting screen:
ISO = 1 For FANUC Device.
I/O = 0 Set PRM No. 2 & 552 for stop bits and baudrate.
1 Set PRM No. 12 & 553 for stop bits and baudrate.
2 Set PRM No. 50 & 250 for stop bits and baudrate.
PRM 2, 12, 50 = 1xxxxxx1 (No feed output, 2 stop bits), PRM 552, 553, 250 = 10 (4800)
Additional parameters:
No. 10.4 Protect programs 9000 ~ 9999. Iron man 3 vostfr uptobox movies.
No. 38.7&6 Device type- 10xxxxxx = RS-232
No. 38.3 Keypad type- 1 = Full keypad, 0 = standard keypad
No. 55.1 End code- 1 = ETX, 0 = CR
No. 57.4 LF or LF/CR- 1 = LF/CR, 0 = LF
Instruction Manual and User Guide for Fanuc 15. We have 32 Fanuc 15 manuals for free PDF download.
Fanuc 15 Manuals
CNC Programming, Operating & Maintenance Manuals
Fanuc 15m Operator Manual
Fanuc Symbol CAPi T Operators Manual B-63304EN/02
Fanuc Open CNC (DNC Operation Management Package) Operators Manual B-63214EN/01
Fanuc Data Server Manuel de l’Opérateur B-62694FR/03
Fanuc Data Server Manuale dell’Operatore B-62694IT/03
FANUC Open CNC (Basic Operation Package 1 for Windows95/NT) Operators Manual B-62994EN/02
Fanuc Servidor de Datos Manual del operador B-62694SP/03
Fanuc 15m Operator Manual Pdf
FANUC Series 15/150-Model B Machining Center Operators Manual (Programming) B-62564E/02
FANUC Series 15/150-Model B Lathe Operators Manual (Programming) B-62554E/01
FANUC Series 15/150-Model B Machining Center Operators Manual (Operation) B-62564E-1/02
FANUC Series 15/150-Model B Parameter Manual B-62560E/02
FANUC Series 15/150-Model B Lathe Operators Manual (Operation) B-62554E-1/01
Fanuc CAP II para torno, Series 15/16/18-TB, 16/16i/18i-TA, 16/18-TC Manual de Operador B-61804SP-2/02
FANUC Series 15-Model B Descriptions Manual for Gas, Laser, Plasma Cutting Machines B-62082E-1/01
FANUC Series 15/150-Model B Descriptions Manual for Machining Center B-62082E/04
Fanuc Conversational Automatic Programming (CAP) Function II for Lathe Operators Manual B-61804E-2/05
Fanuc Series 15/150-Model B Maintenance Manual B-62075E/04
Fanuc Series 15-Model B Operation and Maintenance Handbook B-62077E/01
Fanuc 15-Model B Gas Laser Plasma Cutting Machines Descriptions Manual 62082EN-1
Fanuc 15-MB Connection Manual Hardware
Fanuc 15-Model B Connection Manual BMI Interface 62073E-1
Fanuc 15-Model B Macro Compiler Executer Programming Manual 62073E-2
Fanuc 15-Model B Machining Center Descriptions Manual 62082E
Fanuc Manual Guide I Download
Fanuc 15–MB Programming Manual
Fanuc Guide I Operator's Manual
Fanuc 15-TB Operator’s Manual
Fanuc Programming Manual Pdf
12»